THIS INFORMATION IS OUT OF DATE. READ THE UP TO DATE INFORMATION IN THE USER’S GUIDE
The idea is to execute the LINSTOR controller within a VM that is controlled by Proxmox and its HA features, where the storage resides on DRBD, managed by LINSTOR itself.
Preparing the Storage
The first step is to allocate storage for the VM by creating a VM and selecting “Do not use any media” on the “OS” section. The hard disk should reside on DRBD (e.g., “drbdstorage”). Disk space should be at least 2GB, and for RAM we chose 1GB. These are the minimal requirements for the appliance LINBIT provides to its customers (see below). If you set up your own controller VM, or resources are not constrained, increase these minimal values. In the following, we assume that the controller VM was created with ID 100, but it is fine if this VM is created later (after you have already created other VMs).
LINSTOR Controller Appliance
LINBIT provides an appliance for its customers that can be used to populate the created storage. For the appliance to work, we first create a “Serial Port.” First, click on “Hardware” and then on “Add” and finally on “Serial Port.” See image below:
If everything worked as expected, the VM definition should then look like this:
The next step is to copy the VM appliance to the created storage. This can be done with qemu-img. Make sure to replace the VM ID with the correct one:
# qemu-img dd -O raw if=/tmp/linbit-linstor-controller-amd64.img \ of=/dev/drbd/by-res/vm-100-disk-1/0
After that, you can start the VM and connect to it via the Proxmox VNC viewer. The default user name and password are both “linbit”. Note that we kept the defaults for SSH, so you will not be able to log in to the VM via SSH and username/password. If you want to enable that (and/or “root” login), enable these settings in
/etc/ssh/sshd_config and restart the ssh service. As this VM is based on “Ubuntu Bionic”, you should change your network settings (e.g., static IP) in
/etc/netplan/config.yaml. After that you should be able to ssh to the VM:
Adding the Controller VM to the existing Cluster
In the next step, you add the controller VM to the existing cluster:
# linstor node create --node-type Controller \ linstor-controller 10.43.7.254
As this special VM will be not be managed by the Proxmox Plugin, make sure all hosts have access to that VM’s storage. In our test cluster, we checked the
linstor resource list to confirm where the storage was already deployed and then created further assignments via
linstor resource create. In our lab consisting of four nodes, we made all resource assignments diskful, but diskless assignments are fine as well. As a rule of thumb keep the redundancy count at “3” (more usually does not make sense), and assign the rest diskless.
As the storage for this particular VM has to be made available (i.e.,
drbdadm up), enable the drbd.service on all nodes:
# systemctl enable drbd # systemctl start drbd
At startup, the `linstor-satellite` service deletes all of its resource files (
*.res) and regenerates them. This conflicts with the
drbd services that needs these resource files to start the controller VM. It is good enough to first bring up the resources via
drbd.service and then start
linstor-satellite.service. To make the necessary changes, you need to create a drop-in for the
not edit the file directly).
# systemctl edit linstor-satellite [Unit] After=drbd.service
Switching to the New Controller
Now, it is time for the final steps — namely switching from the existing controller to the new one in the VM. Stop the old controller service on the old host, and copy the LINSTOR controller database to the VM:
# systemctl stop linstor-controller # systemctl disable linstor-controller # scp /var/lib/linstor/* [email protected]:/var/lib/linstor/
Finally, we can enable the controller in the VM:
# systemctl start linstor-controller # in the VM # systemctl enable linstor-controller # in the VM
To check if everything worked as expected, you can query the cluster nodes on a host by asking the controller in the VM:
linstor --controllers=10.43.7.254 node list. It is perfectly fine that the controller (which is just a controller and not “combined”) is shown as “OFFLINE”. Still, this might change in the future to something more appropriate.
As the last – but crucial – step, you need to add the “controllervm” option to
/etc/pve/storage.cfg, and change the controller IP:
drbd: drbdstorage content images,rootdir redundancy 3 controller 10.43.7.254 controllervm 100
By setting the “controllervm” parameter the plugin will ignore (or act accordingly) if there are actions on the controller VM. Basically, this VM should not be managed by the plugin, so the plugin mainly ignores all actions on the given controller VM ID. However, there is one exception. When you delete the VM in the GUI, it is removed from the GUI. We did not find a way to return/kill it in a way that would keep the VM in the GUI. Yet such requests are ignored by the plugin, so the VM will not be deleted from the LINSTOR cluster. Therefore, it is possible to later create a VM with the ID of the old controller. The plugin will just return “OK”, and the old VM with the old data can be used again. To keep it simple, be careful to not delete the controller VM.
Enabling HA for the Controller VM in Proxmox
Currently, we have the controller executed as VM, but we should make sure that one instance of the VM is started at all times. For that we use Proxmox’s HA feature. Click on the VM; then on “More”; and then on “Manage HA.” We set the following parameters for our controller VM:
As long as there are surviving nodes in your Proxmox cluster, everything should be fine. In case the node hosting the controller VM is shut down or lost, Proxmox HA will make sure the controller is started on another host. The IP of the controller VM should not change. It is up to you as admin to make sure this is the case (e.g., setting a static IP, or always providing the same IP via dhcp on the bridged interface).
One limitation that is not fully handled with this setup is a total cluster outage (e.g., common power supply failure) with a restart of all cluster nodes. Proxmox is unfortunately pretty limited in that regard. You can enable the “HA Feature” for a VM, and you can define “Start and Shutdown Order” constraints. But both are completely separated from each other. Therefore it is difficult to ensure that the controller VM is up and all other VMs are started.
It might be possible to work around that by delaying VM startup in the Proxmox plugin until the controller VM is up (i.e., if the plugin is asked to start the controller VM it does it, otherwise it waits and pings the controller). While this is a nice idea, it would be a huge failure in a serialized, non-concurrent VM start/plugin call event stream where some VM should be started (which then blocks) before the controller VM is scheduled to be started. That would obviously result in a deadlock.
We will discuss options with Proxmox, but we think the presented solution is valuable in typical use cases as is, especially compared to the complexity of a Pacemaker setup. Use cases where one can expect that not the whole cluster goes down at the same time are (will be??) covered. And even if that is the case, only automatic startup of the VMs would not work when the whole cluster is started. In such a scenario, the admin just has to wait until the Proxmox HA service starts the controller VM. After that, all VMs can be started manually/scripted on the command line.